Showing 1–16 of 21 results
-
AXM-100 High Voltage Tach Adapter
$65.00Many older tachometers trigger off the negative terminal of the ignition coil. Often, these use a filtering circuit which will not trigger when given a 0 to 12 volt square wave signal, such as the tach output signal from an ECU or ignition box. If you h...
Add to cart -
Sealed resistor – 10K
$4.50We've wrapped a 10K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Red heat shrink tubing with yellow leads. Typically used as a shunt resistor with VR sensors.
Add to cart -
Sealed resistor – 1K
$4.50We've wrapped a 1K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Blue heat shrink tubing with blue leads. Suggested uses include a pull-up resistor for Hall effect and optical sensors, and pull ups for VSS or other 0-12 vol...
Add to cart -
AMPEFI Transmission Controller with 4L80E Subharness
$499.004L80E Plug and Play Transmission Control Seamlessly control your 4L80E transmission with AMPEFI Transmission Control! The supplied 4L80E subharness provides a simple, plug and play integration with MS3Pro and directly mates with our LSx drop on ha...
Add to cart -
AMPEFI Transmission Controller with 4L60E Subharness
$499.00AMPEFI 4L60E Plug and Play Transmission Control Seamlessly control your 4L60E transmission with AMPEFI Transmission Control! The supplied 4L60E subharness provides a simple, plug and play integration with MS3Pro and directly mates with our LSx drop ...
Add to cart -
4 Pin M12 Serial Cable
$29.99Optional, connect MS3Pro ULTIMATE directly to your laptop with this 4 pin M12 serial cable.
Add to cart -
MS3Pro 1st Gen Wiring Harness Upgrade (for ULTIMATE & EVO)
$22.00If you have a previously installed MS3Pro harness (1st Gen) and want to change to an MS3Pro ULTIMATE or EVO ECU, the upgrade path is simple. However, complete functionality will require a few basic changes to your 1st Gen harness. Our wiring upgrade ki...
Add to cart -
MS3Pro EVO Uncrimped AMPSEAL Connectors
$60.00Making your own harness? This plug and pin kit features the MS3-Pro AMPSEAL connectors plus 75 pins (so you'll have a couple extras) for making your own MS3-Pro EVO harness. (or Gen1 if you wish) Download AMPSEAL Assembly Instructions
Add to cart -
USB to Serial Adapter – Trouble Free!!
$28.99Important Note: The original USB2920 was discontinued by its manufacturer. We are now providing an updated part, but we are continuing using the same part number to make it easy for you to find. This FTDI chipset USB to Serial Adapter has been test...
Add to cart -
MicroSquirt Engine Management System with 8′ Wiring Harness
$388.00MicroSquirt Engine Management System with 8' Wiring Harness Version 3.0 The versatile MicroSquirt: Standalone Engine Management System, Transmission Controller or CAN I/O Expansion Module Microsquirt is our entry-level fully assembled ECU with vari...
Add to cart -
MicroSquirt Engine Management System with 30″ Wiring Harness
$360.00MicroSquirt Engine Management System with 30" Wiring Harness Version 3.0 The versatile MicroSquirt: Standalone Engine Management System, Transmission Controller or CAN I/O Expansion Module Microsquirt is our entry-level fully assembled ECU with var...
Add to cart -
MicroSquirt Engine Management System – ECU only
$314.00MicroSquirt Engine Management System Version 3.0 ECU Only - no harness The versatile MicroSquirt Engine Management System, Transmission Controller or CAN I/O Expansion Module is our entry-level fully assembled ECU with varied applications targ...
Add to cart -
Electronic Boost Control (EBC) Solenoid Kit
$58.00This electronic boost control solenoid can be used with the MS3-Pro/MSPNP2 or with other electronic boost controllers to control boost by adjusting the pressure to a turbo wastegate. The MS3-Pro, MS3-Pro Plug and Play, & MSPNP2 can drive this direct...
Add to cart