Showing 17–32 of 32 results
-
HSD-4 High Side Driver with 4 channels
$109.99Have an application with a lot of small solenoids that need 12V power and rapid switching? Don't want the expense of a bank of four separate solid state relays, each rated for five times the current each solenoid needs? This module lets you run up to four...
Add to cart -
AXM-120 VR conditioner
$70.00Use this module to convert the sine wave signal from a VR (variable reluctor) signal into an easy to handle square wave. The AXM-120 VR conditioner works with camshaft position, crankshaft position, vehicle speed, or similar sensors. Common uses for thi...
Add to cart -
AXM-110 High Voltage Isolator
$65.00This module protects your engine or transmission controller from high voltage spikes being fed in through digital inputs. The AXM-110 module can take 1,500 volts peak and 33.5 volts continuous. Common uses for the AXM-110 high voltage isolator include: ...
Add to cart -
AXM-100 High Voltage Tach Adapter
$65.00Many older tachometers trigger off the negative terminal of the ignition coil. Often, these use a filtering circuit which will not trigger when given a 0 to 12 volt square wave signal, such as the tach output signal from an ECU or ignition box. If you h...
Add to cart -
MS3Pro EVO Uncrimped AMPSEAL Connectors
$64.99Making your own harness? This plug and pin kit features the MS3-Pro AMPSEAL connectors plus 75 pins (so you'll have a couple extras) for making your own MS3-Pro EVO harness. (or Gen1 if you wish) Download AMPSEAL Assembly Instructions
Add to cart -
Electronic Boost Control (EBC) Solenoid Kit
$62.99This electronic boost control solenoid can be used with the MS3-Pro/MSPNP2 or with other electronic boost controllers to control boost by adjusting the pressure to a turbo wastegate. The MS3-Pro, MS3-Pro Plug and Play, & MSPNP2 can drive this direct...
Add to cart -
MS3Pro ULTIMATE – Center (Black) Harness Only
$59.99MS3Pro ULTIMATE adds nearly 50% more I/O with the addition of a third AMPSEAL 23-pin, 8' flying lead. Harness arrives with color-coded, printed wires per the pinout below (black center connector) ***Center Harness ONLY in this listing, intended for p...
Add to cart -
4 Pin M12 Serial Cable
$29.99Optional, connect MS3Pro ULTIMATE directly to your laptop with this 4 pin M12 serial cable.
Read more -
USB to Serial Adapter – Trouble Free!!
$28.99This FTDI chipset USB to Serial Adapter has been tested and works properly with all of our ECU products and all versions of TunerStudio on a wide range of operating systems. This is probably the most common item we see people come back for after a purch...
Add to cart -
MS3Pro 1st Gen Wiring Harness Upgrade (for ULTIMATE & EVO)
$23.99If you have a previously installed MS3Pro harness (1st Gen) and want to change to an MS3Pro ULTIMATE or EVO ECU, the upgrade path is simple. However, complete functionality will require a few basic changes to your 1st Gen harness. Our wiring upgrade ki...
Add to cart -
Sealed resistor – 10K
$4.50We've wrapped a 10K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Red heat shrink tubing with yellow leads. Typically used as a shunt resistor with VR sensors.
Add to cart -
Sealed resistor – 1K
$4.50We've wrapped a 1K, 1/4 watt resistor in a sealed and strain-relieved package for underhood use. Blue heat shrink tubing with blue leads. Suggested uses include a pull-up resistor for Hall effect and optical sensors, and pull ups for VSS or other 0-12 vol...
Add to cart -
MS3Pro Ultimate + EVO F5 Replacement Fuse
$3.00The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand. These 500mA fus...
Add to cart -
MS3Pro Module F1/F2 Replacement Fuse
$3.00The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand. This is the 100...
Add to cart -
Gen 1 MS3Pro F1/F2 + EVO F4 Replacement Fuse
$2.25The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand. These 500mA fus...
Add to cart -
MS3Pro Ultimate F4/F6 Replacement Fuse
$2.00The MS3Pro ECU’s feature user-replaceable fuses that protect against voltage spikes and other abuse. To replace these fuses, use a needle nose pliers to pull the fuse out of its holder, and then push in the replacement fuse by hand. This is the 375...
Add to cart