Cart

Quick Links

Mazda Miata 1999-2000 MSPNP Gen2 Plug and Play ECU

From: $839.00

Product Quantity

USB to Serial Adapter - Trouble Free!! – optional

In stock (can be backordered)

In stock (can be backordered)

SKU: MSPNP2-MM9900 Category: Tags: , , , , , , , , , , , , Brand:

Description

MSPNP2 Plug and Play Standalone Engine Management System

1999-2000 USDM Mazda Miata w/ manual transmission

Second Generation MSPNP; Easy to Use and Install!    

MSPNP2 Model #MM9900 Features:

  • Fully Plug and Play Installation – No wiring required for basic functionality.  Average install time is under 1 hour!
  • Base map is pre-loaded to help your engine start on the first turn of the key
  • Real time tuning and data logging with a laptop connection
  • Supports most aftermarket wideband sensors

Fully Tunable Engine Control!

  • 16×16 Fuel Tables allow high resolution tuning
  • 12×12 Ignition Tables
  • Multiple Acceleration enrichment strategies
  • Closed Loop Idle Speed Control
  • Air Conditioner Control
  • 4 sequential fuel injector channels with individual trim tables
  • Onboard peak and hold drivers support both high and low impedance injectors – No external ballast resistor is needed!
  • Allows removal of stock airflow meter
  • Controls stock alternator (alternator control not adjustable)

Advanced Feature Set (Included!)

  • 12×12 Air Fuel Ratio Target Tables for use with wide band O2 sensor for precise tuning and table trim.
  • Built-in 2-step rev limiter / launch control with flat shift
  • Real time barometric correction
  • Internal 4-bar MAP sensor reads up to 44PSI of boost
  • Overboost protection
  • Closed loop boost control (Requires DIYAutoTune.com EBC solenoid kit)
  • Knock sensor input with adjustable sensitivity
  • Headphone output for knock sensor – listen for knock while you tune!
  • Table switching input. Change fuel and spark maps on the fly for different fuels, nitrous activation, etc.
  • Input for flex fuel sensor – switch between E85 and gasoline on the fly!
  • CANBus connector allows interconnection of other MegaSquirt-compatible devices for additional functions (EGT Input, Automatic Transmission Controller, Additional Sensors…..the possibilities are limitless!

What you get in the box:

    • MSPNP2 Standalone Plug and Play MM9900 ECU
    • MSPNP RS232 serial tuning cable, 6′ (USB adapter sold separately, if needed)
    • Tuning Software and Documentation USB Stick
    • 6′ Vacuum Hose for MAP Signal and ‘T’ fitting
    • Four Screws for ECU mounting

Note: Although there is a paid upgrade to TunerStudio, it is not needed to tune this ECU. The free version included on the USB Stick can access all the features and tables of the MegaSquirtPNP. The paid version of TunerStudio simply adds tuning and analysis software, such as VE Analyzer Live to tune the fuel tables based on wideband O2 feedback (requiring a wideband O2 sensor and controller, sold separately).

Customer reviews

5 stars 0 0 %
4 stars 0 0 %
3 stars 0 0 %
2 stars 0 0 %
1 star 0 0 %

Reviews

There are no reviews yet.

Be the first to review “Mazda Miata 1999-2000 MSPNP Gen2 Plug and Play ECU”

Where is this product assembled?

  • This product is assembled in Suwanee, Georgia, USA

I have swapped a different year engine, will this still work?

  • You must use the MSPNP that matches the year of the engine harness you are using.

Is this all that I need to get started tuning my Miata?

  • The only other potential must-have is that if your laptop doesn’t have a 9 pin serial port, you will need our USB to serial adapter to connect to this unit. However, there are several other things you may wish to add to use this unit to its full potential.

Do I need to swap to a GM style intake air temperature to remove the mass air flow sensor?

  • On ’99-’00 Miatas, the IAT sensor is separate from the mass air flow sensor, so it is not necessary to get a GM type sensor if removing the MAF. However, if you are relocating the IAT sensor for a turbo installation, it is often easier to use a threaded IAT sensor such as the GM design.

Will this control VVT if I swap in a later VVT Miata engine?

  • This unit does not support VVT.  We recommend starting with an MSPNP Pro if you have or are planning a VVT swap. If you already have this ECU, you could add our VVTuner piggyback device.

What is the difference between the MSPNP Gen 2 and the MSPNP Pro?

  • The MSPNP Gen 2 will provide fuel and ignition control, plus some basic race features such as launch control and boost control. The MSPNP Pro adds a number of advanced features, such as:
    • Programmable alternator voltage control that you can adjust through TunerStudio
    • VVT control for ’01-’05 engine swaps
    • Sequential spark control for coil per plug conversions
    • Eight fuel channels to allow for a fifth injector control or staged sequential injection
    • Boost by gear or ground speed
    • Timed boost delay and spark retard activated by launch control
    • Traction control
    • Rally style anti-lag
    • Advanced flex fuel support that allows blending almost all fuel and ignition tables based on fuel composition
    • Progressive nitrous control
    • Variable water injection control

Questions & Answers

There are no questions yet, be the first to ask something for this product.

Send me a notification for each new answer.

You may also like…

  • Mazda Miata 1999-2000 MS3Pro PnP Plug and Play

    5 out of 5
    From: $1,199.00

      MS3-Pro Plug and Play takes engine management to the next level!  Easy to Use and Install! MS3-Pro Plug and Play Model #MM9900 Features: Fully Plug and Play Installation - No wiring required for basic functionality Average instal...

    Add to cart
  • USB to Serial Adapter – Trouble Free!!

    4.7142857142857 out of 5
    $28.99

    Important Note:  The original USB2920 was discontinued by its manufacturer.  We are now providing an updated part, but we are continuing using the same part number to make it easy for you to find. This FTDI chipset USB to Serial Adapter has been test...

    Add to cart
  • Innovate Standalone Gauge Kit with LC-2 & Red DB Gauge – 3796

    $219.00

    Innovate Standalone Gauge Kit with LC-2 & Red DB Digital Gauge Innovate Motorsports introduces their newest digital gauge option for those looking for affordable wideband monitoring. The Innovate “Standalone Gauge Kit” comes complete with the p...

    Add to cart
  • Electronic Boost Control (EBC) Solenoid Kit

    $58.00

    This electronic boost control solenoid can be used with the MS3-Pro/MSPNP2 or with other electronic boost controllers to control boost by adjusting the pressure to a turbo wastegate. The MS3-Pro, MS3-Pro Plug and Play, & MSPNP2 can drive this direct...

    Add to cart
  • MS3Pro Standalone ECU with 8′ Wiring Harness

    5 out of 5
    $1,199.00

    IMPORTANT PRODUCT UPDATE**  MS3Pro-Pkg1 has been discontinued and superseded by MS3Pro EVO effective May 1, 2017.  This product page, including documentation, downloads & product FAQ tabs below, remains active for archive purposes.   Compare MS...

    Read more